Seat Instructions for Adding Accessories and Replacing Parts

Stadium Seats, etc., Inc.

713 Angers Street
New Iberia, LA  70563-1935
Phone:  337-367-5577 or 877-527-3986
Fax:  337-367-5596 or 877-367-5596
E-Mail:  stadiumseats@cox.net
Website:  stadiumseatsetc.com

Instructions for Adding Cup holder

1. Locate the hole that has been pre-drilled in the plastic and aluminum channel below the cushioned seat bottom.

2. Place the bent aluminum arm at the end of the cup holder in the pre-drilled hole making sure that it is inserted through both the plastic first and then through the aluminum channel.

3. Swivel the cup holder between the cushioned seat bottom and the plastic when not in use.

 Instructions for Adding Mesh Bag

1. Remove the screw that secures the seat back to the seat frame.

2. Remove the seat back from the seat frame by pulling it straight up.
   

3. Return the furniture tips to the seat frame if they were removed when completing step 2 above.
   

4. Slide the top part of the mesh bag onto the seat frame.  Make sure the zipper on the mesh bag is facing the front part of the seat (i.e., the seat cushion).
   

5. Slide the colored seat back onto the seat frame (over the mesh bag).
   

6. Reattach the screw that secures the seat back to the seat frame.
   

7. Open the snap and wrap it around the pipe at the bottom portion of the seat back frame then close the snap.

 NOTE:  You may need to place the seat on its side with the seat back in the open position and place a light amount of pressure on the seat back frame to remove and replace the seat back and to add the mesh bag.

 Instructions For Adding Seat Back Cushion

1. Unscrew and remove the screw that secures the seat back to the frame.

2. Turn the stadium seat on its side with the seat back in an upright seating position.
   

3. Push down slightly on the seat back frame in order to loosen the seat back then slide the seat back off of the frame.
   

4. Make sure the two furniture tips remain on the top of the seat back frame.
   

5. Insert the seat back cushion into the colored seat back fabric making sure that the ¾” piece of black nylon strapping at the bottom of the seat back cushion is on the same side as the drilled hole on the seat back frame (so that the seat back cushion can be attached to the seat frame).
   

6. With the seat still on it side, push down slightly on the seat back frame and slide the seat back cushion and colored seat back fabric on to the seat back frame.
   

7. Reattach the screw to secure the seat back to the seat frame.

 Instructions for Replacing Seat Backs

1. Remove the seat back by unscrewing the small screw that secures the seat back to the seat frame.
   

2. Put the new seat back on the seat by placing it at the top of the frame and slowly sliding it down. The advertisement label should be to the back of the seat.

 NOTE:  You may need to place the seat on its side with the seat back in the open position and place a light amount of pressure on the seat back frame to remove and replace the seat back.

 Instructions for Replacing Seat Bottoms

1. Close the seat back and turn the seat so that the bottom of the seat is facing upward.

2. Unscrew the 4 screws that secure the seat bottom to the seat frame.
   

3. Open the Velcro and remove the foam from the seat bottom fabric.
   

4. Place the foam in the new fabric ensuring that the 3” thick portion of the foam is to the back of the fabric (near the Velcro area) and the 2” thick portion of the foam is to the front of the fabric.  Before closing the Velcro work the foam with your hand to make sure that it is set properly in the fabric.  Also make sure that the ends of the strapping (the four pieces) are laying flat on the bottom of the foam.
   

5. Close the Velcro.
   

6. Reattach the seat bottom to the seat frame using the 4 screws.